BINSFELD ENGINEERING INC.

FAQ

 

Frequently Asked Questions

What is an RTD?
What is a rotary temperature transmitter and what does it do?
Why is it better to use a rotating temperature sensor instead of a stationary sensor?
What is a thermocouple?
Can a godet roll motor assembly be converted from using a stationary sensor to a rotating sensor?
Why is a digital temperature transmitter better than an analog transmitter?
How does the TempTrak® transmitter work with a 9 mm gap between rotating and stationary parts when most transmitters require a 1 mm gap?
How does godet temperature affect yarn properties?
Why does Binsfeld locate the stationary circuit of the transmitter system in a separate controller interface instead of locating it in the stationary housing on the roll motor?
How far can the Binsfeld Controller Interface be located from the Binsfeld Transmitter?
Will the TempTrak® Transmitter fit any godet roll motor assembly?
What is covered under Binsfeld's five-year warranty?
Can the TempTrak® Transmitter accommodate a through-shaft?
Can the TempTrak® Transmitter accommodate non-standard RTDs?
Where can I find information on Binsfeld's torque measuring products?

Click here to contact our experts and learn more!


What is an RTD?

An RTD (Resistive Temperature Device) is a sensor that changes resistance with temperature in a linear relationship. RTDs are the most common temperature sensors used with rotary temperature transmitters. They may be specified as PT-100 indicating platinum-tungsten with a resistance of 100 ohms at 0° C, PT-200, or PT-2000 and typically have a temperature coefficient of a = 0.00385.      BACK

 

What is a rotary temperature transmitter and what does it do?

A rotary temperature transmitter communicates a temperature sensor signal from a rotating godet (draw roll) to a stationary process control system that regulates the heater under the godet.      BACK

 

Why is it better to use a rotating temperature sensor instead of a stationary sensor?

A rotating sensor senses the temperature of the godet roll shell directly under the yarn wrap, exactly where the temperature must be controlled. A stationary sensor measures the temperature in an air gap near the base of the godet, far from the yarn wrap, introducing errors that vary with distance from yarn wrap, location of sensor in air gap, roll speed, ambient air temperature and humidity and desired process control temperature. A stationary sensor can be "tuned in" manually, but as soon as there is a change in any of the parameters listed above it will drift out of calibration.      BACK

 

What is a thermocouple?

A thermocouple is another type of temperature sensor in which two wires of different metals (e.g. Iron and Constantine) are connected together at the point of temperature measurement (hot junction) and connected at the other end in an ambient temperature location (cold or reference junction). The dissimilar metals generate a low level current from the hot junction to the cold junction that is sensed. Although these devices are very simple and robust, they are not linear and the requirement for a cold reference junction means they are typically not suitable for rotary temperature use.      BACK
 

Can a godet roll motor assembly be converted from using a stationary sensor to a rotating sensor?

Not easily. To accommodate a rotating sensor and rotary temperature transmitter the godet needs to be modified to accept an RTD in the wall of the roll shell under the yarn wrap, the roll motor shaft needs to be gun drilled through to allow the RTD lead wires to exit out of the back of the roll motor and the rotary transmitter needs to be fitted to the rear motor shaft.      BACK

 

Why is a digital temperature transmitter better than an analog transmitter?

A key advantage to digital measurement is that you only measure once - at the sensor. The measurement is immediately converted to a digital "word" for further processing (e.g. transmitting from the rotating transmitter to the stationary pickup) so it's a fixed value that can't be altered in the process. In contrast, an analog measurement is re-measured at each step in the process (e.g. it may be converted to a frequency to send from the rotating transmitter to the stationary pickup and that frequency must be accurately re-measured on the stationary side). Each time it is re-measured, the opportunity for error is introduced.      BACK
 

How does the TempTrak®transmitter work with a 9 mm gap between rotating and stationary parts when most transmitters require a 1 mm gap?

The TempTrak® transmitter uses a tuned resonant inductive coupling, which allows the power and data to transmit over a greater gap. It also allows a generous +/- 3 mm adjustment tolerance, which eliminates any critical positioning during installation. In addition, because the TempTrak® system sends digital language across the gap, it is able to constantly monitor and optimize the power level of the rotor, which would otherwise vary with the transmitter spacing.      BACK
 

How does godet temperature affect yarn properties?

Poor godet temperature control can have a negative affect on yarn quality. Yarn color is a primary concern, whether the color is introduced in the extruder or later in a dyeing process. An off-color thread line in a solid color weave will appear as streaking. Mechanical properties of the yarn including tenacity (stiffness), emissivity (how light reflects) and strength are also affected by godet roll temperature.      BACK
 

Why does Binsfeld locate the stationary circuit of the transmitter system in a separate controller interface instead of locating it in the stationary housing on the roll motor?

Elevated temperatures can shorten the life of electronic components. Locating the stationary circuit away from the hot harsh roll motor environment helps achieve the outstanding reliability of the TempTrak® transmitter. The simple DIN-rail controller interface takes up minimal room and typically fits in an existing cabinet where it is immediately accessible to evaluate any error codes - codes that direct the operator to problems in the temperature control system that are quickly remedied (e.g. failed sensor) without having to pull the motor assembly for troubleshooting.      BACK
 

How far can the Binsfeld Controller Interface be located from the Binsfeld Transmitter?

The transmitter on the back of the godet roll motor assembly is connected to the Controller Interface by a coax cable. The maximum recommended length of this cable is 30 meters (100 feet). This is typically more than enough length to remove the controller interface from the harsh motor environment.      BACK
 

Will the TempTrak®Transmitter fit any godet roll motor assembly?

The TempTrak® Transmitter's flexible mounting style allows it to fit most machines. Mechanical configurations for Rieter, Neumag, Barmag, Erdmann, Toray, Plantex, G.E., Fycon, PASCO, ISGEV and others are available. If your roll motor does not meet one of these existing designs, Binsfeld will create a mechanical configuration to suit your needs. A design configuration fee is charged for this service, but is waived if 4 or more systems are ordered.      BACK
 

What is covered under Binsfeld's five-year warranty?

Simply stated, everything except fuses, paint and misuse are covered. For the complete warranty text, please contact us.      BACK
 

Can the TempTrak® Transmitter accommodate a through-shaft?

Yes, the TempTrak design allows for shafts up to 30 mm to pass through the rotating transmitter and stationary pickup. This allows it to be used in applications where there is an outboard sheave (e.g. belt driven godet) or where the transmitter must be located between the motor and the roll assembly.      BACK

 

Can the TempTrak®Transmitter accommodate non-standard RTDs?

Yes. If you provide the temperature table or curve for your non-standard sensor, Binsfeld can program the transmitter to work with it.      BACK
 

Where can I find information on Binsfeld's torque measuring products?

Binsfeld's torque measuring products can be found here.